A metro that heats with radiators and cools with window units, in buildings that were never given a place to put ductwork.
The heating and cooling problem in this metro is architectural before it is mechanical. Almost half the housing predates 1980 and only 44.2% is single-family detached, so the typical job is a rowhouse or a mid-century apartment building with a boiler in the basement, cast-iron radiators under the windows, no return-air path between floors, and no closet big enough to hide a duct chase. Cooling was added later, one window unit at a time. Any real upgrade has to answer the same question: where does the air go, and what happens to the walls when it does.
Many older houses and small apartment buildings here run on a gas boiler and cast-iron radiators, which is a comfortable system when it works and an expensive one when it is scaled and unbalanced. The decision is rarely all-or-nothing: a boiler can be retained while a heat pump takes over the shoulder seasons, or the radiators can stay as the distribution for a new source. Ask what condition the boiler is in, whether the system has been balanced, whether a domestic-hot-water coil shares the boiler, and what a partial conversion would actually look like.
Where there is no duct chase — and in a brick rowhouse there usually is not — ductless mini-splits are the pragmatic answer: a head in each room that needs conditioning, a line set run along an exterior wall or through a closet, and a condenser outside. The trade-offs are real. Exterior equipment placement can conflict with historic district review, line-set routing has to avoid visible front facades, and a multi-zone system must be sized per room rather than by total square footage. Ask how many zones are proposed, where the outdoor units will sit, and how the line sets will be concealed.
A DC summer loads a system with latent heat as much as sensible heat, and that is where undersized or badly set-up equipment fails: the room reaches temperature quickly and stays clammy. Short cycling from an oversized unit makes it worse, because the coil never runs long enough to remove moisture. Ask whether the proposal includes a load calculation that accounts for humidity, whether the equipment can run at reduced capacity for longer, and whether a dedicated dehumidifier is part of the answer for a basement.
The District's building performance rules have pushed large buildings toward measured energy performance, and federal efficiency standards have narrowed the equipment available. Practically, that means the choice between repairing and replacing is increasingly made on efficiency and refrigerant transition, not only on age. Ask what refrigerant the proposed equipment uses, whether replacement parts will be available for the existing system, what the installed efficiency rating is, and — for a larger building — whether the owner has obligations under the local performance standard that the mechanical work should support.
In a brick rowhouse the envelope is where the load is created: open chases between floors, unsealed penetrations where ducts and pipes pass through, a cellar door that is effectively a hole in the wall, and a top-floor ceiling that meets a hot roof deck. Sealing those paths can change the size of the equipment a house needs, which is why the sequence matters. Ask whether air sealing is part of the scope, what gets sealed at the attic floor and the rim, and whether the sizing assumed the sealing would happen.
- Is there a room-by-room load calculation, or a rule-of-thumb sizing? - What happens to the existing boiler and radiators — retained, replaced or abandoned? - How many zones, where do the heads go, and where does the outdoor unit sit? - Is historic district review needed for exterior equipment or line-set routing? - How is humidity addressed, and is a dehumidifier included for the basement? - What refrigerant and efficiency rating, and what warranty applies to the install?
No prices, sizes or efficiency figures are quoted here, and no building is assessed. Sizing, refrigerant rules and local performance requirements change, and the applicable version should be confirmed with the manufacturer's literature and the local authority rather than taken from any page.
The 2024 ACS 5-year estimates describe about 6.32 million residents in 2,373,022 households and 2,506,631 housing units, with 63.7% owner-occupied and 44.2% single-family detached. About 45.5% of units predate 1980, which is why hydronic systems and uninsulated walls are still common in the older core. No climate station is reported for this metro in the site dataset, so no temperature or precipitation normals appear on this page.
| Indicator | Value | Source |
|---|---|---|
| Housing units built before 1980 | 45.5% | U.S. Census Bureau |
| Single-family detached share | 44.2% | U.S. Census Bureau |
| Owner-occupied share | 63.7% | U.S. Census Bureau |
| Metro households | 2,373,022 | U.S. Census Bureau |
| Housing units | 2,506,631 | U.S. Census Bureau |
| Metro population | 6,318,377 | U.S. Census Bureau |
No climate normals are shown because no station record is held for this metro in the site dataset. The low detached share is the reason ductless systems and per-room zoning come up more often here than in most metros.
Reviewed on 2026-11-18.