Three problems, one cause each: mineral content, foundations without basements, and pipes in attics that see freezing weather a few nights a year.
San Antonio plumbing is shaped by three things. The water is notably hard, which shortens the life of every appliance that heats it. Almost every house sits on a slab, so a supply leak has nowhere to show itself except through the floor. And a meaningful share of the piping runs through the attic, because that is how plumbing is done in a warm climate with no basement — which works perfectly until the few nights a year when it goes below freezing. The freeze of 2021 made that third point nationally visible, and it changed how plumbers here talk about pipe protection.
Mineral scale builds on tank floors, elements and heat exchangers, lowering efficiency before anything fails. It also clogs aerators and shower heads, stiffens shut-off valves until they no longer close, and shortens the life of a water heater. Softening is common here for those reasons, and it is a decision with trade-offs: salt, maintenance and a discharge line that has to comply with local rules. Ask what the measured hardness at the property is, what the equipment would be sized to, and what it will discharge and where.
Under-slab copper fails by pinhole, and in hard water the process is quicker. The symptoms are indirect — a warm patch on the floor, a climbing bill, the sound of running water with everything off — and confirmation means isolating and pressure-testing rather than opening the floor on a guess. One leak can be repaired; a second within a year or two usually means the run is going, and the choice becomes a repipe through the attic or the walls. Ask how many leaks the system has had, whether a line can be isolated and tested, and which route a repipe would take.
Attic plumbing is the exposed edge of this housing type. On a hard freeze, the pipe that splits is usually in an uninsulated run, at a fitting, or where it passes through a vented soffit — and the damage appears at the thaw when water starts moving at full pressure. Insulating the runs, protecting the attic penetrations and knowing how to shut the house down are cheap compared with what a burst attic line does to two ceilings and a floor. Ask whether the attic runs will be insulated and supported, whether any exposed piping can be rerouted, and where the main shut-off is.
High street pressure stresses every fitting and appliance, and a regulator that has failed open is a common find on a house that keeps developing leaks. On the drainage side, older laterals may be cast iron or clay, and mature trees and long runs find the joints. Outdoors, irrigation runs constantly in a hot climate, and a slow leak outside is invisible. Ask for a static pressure reading, whether a regulator is fitted, whether the lateral has been inspected, and whether the irrigation has its own isolation valve and backflow protection.
Because the water is hard, treatment equipment is common here, and it brings its own maintenance: salt that has to be replenished, resin that has to be kept clean, and a discharge line that has to go somewhere compliant. A softener that is installed and forgotten can become the next problem. Ask what the equipment is sized for, where the brine discharges, who services it, and whether the hardness was measured before the equipment was chosen.
- What is the measured hardness, and is softening being proposed? - How many supply leaks has the system had, and can the line be pressure-tested? - Would a repipe run through the attic or the walls? - Are the attic runs insulated, and how are penetrations protected? - What is the static pressure, and is the regulator working? - Has the lateral been inspected, and does the irrigation have backflow protection?
No prices are quoted and no system is diagnosed here. Water quality, backflow requirements and discharge rules belong to the local utility, and a leak beneath a slab has to be located by inspection.
The 2024 ACS 5-year estimates describe about 2.66 million residents in 967,488 households and 1,057,823 housing units, with 63.3% owner-occupied and 66.1% single-family detached. About 32.7% of units predate 1980. At the reference station January averages 52.2°F and July 84.8°F, with 32.4 inches of annual precipitation — mild on average, but cold enough on occasion to freeze an uninsulated attic line.
| Indicator | Value | Source |
|---|---|---|
| January mean temperature | 52.2°F | NOAA NCEI |
| July mean temperature | 84.8°F | NOAA NCEI |
| Annual precipitation | 32.4 in. | NOAA NCEI |
| Metro population | 2,662,733 | U.S. Census Bureau |
| Owner-occupied share | 63.3% | U.S. Census Bureau |
| Housing units built before 1980 | 32.7% | U.S. Census Bureau |
Station normals are historical averages for one location, not a forecast. A mild average January is exactly why attic plumbing is rarely insulated here, and why a hard freeze finds it.
Reviewed on 2026-11-18.