Where the panel sits above the ground is as important here as what is inside it.
Electrical work in New Orleans begins with elevation. In a metro where much of the housing stands on piers, and where construction in flood zones is regulated around how high equipment sits, the position of a panel, a meter, a condenser or a generator connection is a code question before it is a convenience question. That is layered onto a housing stock where 63.5% of units predate 1980 and a large part of it predates 1950, much of it built as raised or shotgun houses with service equipment added and extended over decades. The result is that a straightforward-sounding job often has a site question at its center.
Property in flood zones is subject to requirements about how high electrical equipment is installed, and the rules have been revised over the years. A panel moved during a renovation, a condenser set on the ground, or a meter reinstalled at the old height can all become compliance problems later. Ask where the equipment will be mounted, what elevation the address requires, and whether the contractor has verified that with the local permitting authority rather than assuming the previous installation was correct. This is the single most local question in the whole trade here.
A raised house built in the 1920s and renovated in the 1970s and again after 2005 commonly contains three generations of wiring: original knob-and-tube in parts of the walls, non-metallic cable from a mid-century upgrade, and modern romex from a recent kitchen. Each renovation added what was current without removing what was there. Ask which circuits are still on the oldest wiring, whether equipment grounding is continuous on the circuits serving modern appliances, and whether the panel schedule reflects what is actually installed. In a house that has been reworked repeatedly, verifying the schedule is not optional.
Long humid seasons are hard on electrical equipment: corrosion at terminals, moisture inside exterior enclosures, and connections that degrade slowly under a house that stands open to the air. Under a raised floor, wiring is exposed to the same damp conditions as the structure. Ask whether exterior and under-floor devices are rated for wet locations, whether covers and gaskets are intact, and whether ground-fault protection exists where it should. These are inexpensive components that prevent the kind of fault that is hard to trace.
Storm season makes backup power a normal purchase rather than a specialty item, and the electrical detail that matters is how a generator connects. A transfer switch or a listed interlock prevents the main and the generator from being energized at the same time, which protects utility crews working on lines outside as well as the household. Ask what transfer equipment is proposed, whether the panel accepts an interlock for that model, what the generator is expected to carry, and where the equipment will be mounted relative to flood elevation.
Electrical work is permitted and inspected locally, and parts of the metro are inside historic districts where exterior changes — a meter relocation, a new disconnect, equipment visible from the street — can require review in addition to the electrical permit. Ask who pulls the permit, who meets the inspector, whether the address is in a district, and what happens if the inspection finds work that predates the current job. In a stock this old, that last question is common enough to be planned for rather than treated as bad luck.
- What elevation does this address require for panels, meters and condensers? - Which circuits remain on the oldest wiring, and what is proposed for them? - Does the panel schedule match what is actually installed? - For a generator, what transfer equipment is used and where is it mounted? - Is the address inside a historic district, and does it add a review step? - Who pulls the permit, and who handles anything the inspection uncovers?
No specific property is assessed here and no prices are published. Electrical hazards, service capacity and flood-zone compliance require on-site evaluation by a licensed electrician, and permit and elevation requirements belong to the local authority.
The 2024 ACS 5-year estimates count about 982,000 residents in 398,564 households across 465,148 housing units. Owner occupancy is 60.6%, about 58.4% of units are single-family detached — lower than in most Southern metros, reflecting the number of doubles and multi-unit buildings — and 63.5% were built before 1980. A climate station is not reported for this metro in the site dataset, so no temperature figures are published on this page.
| Indicator | Value | Source |
|---|---|---|
| Metro population | 981,662 | U.S. Census Bureau |
| Metro households | 398,564 | U.S. Census Bureau |
| Housing units | 465,148 | U.S. Census Bureau |
| Housing units built before 1980 | 63.5% | U.S. Census Bureau |
| Single-family detached share | 58.4% | U.S. Census Bureau |
| Owner-occupied share | 60.6% | U.S. Census Bureau |
A climate station is not reported for this metro in the site dataset, so no temperature normals are shown. Flood-zone elevation requirements are set by the local authority and vary by address.
Reviewed on 2026-11-18.