Trades Across US Trades Across US

Orlando, FL · metro guide

Plumbing in Orlando: Hard Water, Slab Leaks and 1980s Piping

A young housing stock with old problems: hard water, buried pipe and a building boom that used materials now out of favor.

Metro snapshot

Orlando in numbers

Sources named below each block

Population
2.8M
Households
1.0M
Housing units
1.1M
People / household
2.73
population ÷ households

Owner-occupied homes 63%

The rest are rented. Owners are the ones who commission most exterior work.

Single-family detached 59%

Detached houses carry their own roof, gutters and exterior walls.

Built before 1980 24%

Older housing stock shapes what fails first: gutters, flashing, pipe material.

Season

The year in Orlando

Precipitation
51.5 in
Snowfall
0 in

Average temperature by month, °F — the shape of the year is what decides when exterior work gets done.

Precipitation by month, inches.

Monthly climate normals for Orlando
Month Average temperature (°F) Precipitation (in) Snowfall (in)
January 60.6°F 2.48 in 0.0 in
February 63.6°F 2.04 in 0.0 in
March 67.3°F 3.03 in 0.0 in
April 72.2°F 2.58 in 0.0 in
May 77.3°F 4.02 in 0.0 in
June 81.2°F 8.05 in 0.0 in
July 82.6°F 7.46 in 0.0 in
August 82.6°F 7.69 in 0.0 in
September 81.0°F 6.37 in 0.0 in
October 75.5°F 3.46 in 0.0 in
November 68.2°F 1.79 in 0.0 in
December 63.3°F 2.48 in 0.0 in

NOAA 1991–2020 climate normals, station ORLANDO INTL AP, FL US (USW00012815). Station observations, not a metro-wide average — a metro that spans a mountain range can differ by more than this record shows.

Population, households and housing shares: U.S. Census Bureau, American Community Survey 2024 5-year estimates, metropolitan statistical area.

Plumber repairing a water supply pipe during a residential plumbing service call — Orlando–Kissimmee–Sanford

The housing here is young — only 23.8% of units predate 1980 — but plumbing failures are not a function of age alone. Water drawn from the Florida aquifer is mineral-heavy, almost everything is built on a slab, and the construction booms of the 1980s and 1990s used piping materials that are now known to fail. The result is a metro where a thirty-year-old house can present the same repipe decision as a century-old one elsewhere, and where the first symptom is often a jump in the water bill or a warm patch on a tile floor rather than water in a basement the house does not have.

Hard water and what it actually costs

Mineral content shortens the life of a water heater, scales tankless units, clogs aerators and shower heads, and leaves deposits on fixtures that no cleaner removes. It also makes every other problem worse: a scaled heater runs hotter, scale on valves makes shut-offs unreliable, and a softener that is mentioned but never sized correctly simply moves the problem. Whether to treat the water is a real decision — a softener protects equipment but adds salt, maintenance and a discharge line that has to go somewhere compliant. Ask what the measured hardness is at the property, what the equipment would be sized to, and where the brine would discharge.

Slab leaks and the repipe decision

Under-slab supply lines in this soil and water chemistry develop leaks, and the diagnosis is indirect: a hot spot on the floor, the sound of water with everything off, a climbing bill. A single leak can be repaired, but the pattern matters — a second failure within a year or two usually means the run is going, and each repair takes out more flooring. The alternative is a repipe, either through the attic or through the walls, abandoning the under-slab lines. Ask how many leaks the system has had, whether a section can be isolated and pressure-tested, and which route a repipe would take in this house.

Polybutylene and the boom-era piping

A number of houses built in the late 1970s through the 1990s were plumbed in polybutylene, which becomes brittle with age and fails at fittings — often suddenly and usually inside a wall. It is a known risk that insurers ask about and inspectors flag, and it is not something to repair at one fitting, because the material itself is the issue. Older properties may instead have galvanized steel that has corroded closed until the shower barely runs. Ask what material the existing piping is, where it is accessible, and whether a repipe would run overhead or in the walls.

Irrigation, pressure and the outdoor side

A great deal of the plumbing work here is outdoors: irrigation systems with their own valves and lines, hose bibs in sun, pool equipment, and a main shut-off that may not be where the owner expects. Backflow protection on an irrigation system is required in most places and protects the drinking water in the house, so it is worth confirming rather than assuming. Pressure matters too — a failed regulator lets street pressure stress every fitting and appliance. Ask for a static pressure reading, whether the irrigation has backflow protection, and where the main shut-off is and whether it actually closes.

Water heaters in a closet or a garage

Water heaters here are usually in a closet, a garage or an attic — rarely somewhere a leak would be noticed quickly. In a closet the failure soaks the surrounding walls and floor before anyone sees water; in an attic above a ceiling it does the same from the other direction. Hard water shortens the tank's life at the same time. Ask where the heater sits, whether there is a pan and a drain line, whether an expansion tank is fitted, and how the unit is vented if it is gas.

What to pin down in the estimate

  • What is the measured hardness, and is water treatment being proposed?
  • How many leaks has the system had, and can the line be pressure-tested?
  • What piping material is installed, and is any of it polybutylene?
  • Would a repipe run overhead, in the walls, or both?
  • What is the static pressure, and is the regulator working?
  • Does the irrigation system have backflow protection, and where is the main shut-off?
  • Where this page stops

    No prices are quoted and no system is diagnosed here. Water quality, backflow requirements and discharge rules for treatment equipment belong to the local utility, and a leak beneath a slab has to be located by inspection rather than inferred.

    Orlando metro context

    The 2024 ACS 5-year estimates describe about 2.79 million residents in 1,022,315 households and 1,145,360 housing units, with 63.1% owner-occupied and 58.5% single-family detached. Only 23.8% of units predate 1980, so the plumbing questions here cluster around homes built during the boom decades rather than around pre-war housing. No climate station is reported for this metro in the site dataset, so no temperature or precipitation normals appear on this page.

    Orlando housing indicators

    U.S. Census Bureau ACS 2024 5-year estimates, CBSA tables.
    IndicatorValueSource
    Housing units built before 198023.8%U.S. Census Bureau
    Single-family detached share58.5%U.S. Census Bureau
    Owner-occupied share63.1%U.S. Census Bureau
    Metro households1,022,315U.S. Census Bureau
    Housing units1,145,360U.S. Census Bureau
    Metro population2,793,746U.S. Census Bureau

    No climate normals are shown because no station record is held for this metro in the site dataset. Water chemistry varies by utility and by well, so hardness should be measured at the property rather than assumed from the region.

    Frequently Asked Questions

    How do I know if my house has polybutylene pipe?

    It is usually gray or blue-gray plastic, often marked with a product code, and it is found at the water heater connections and under sinks. A plumber can confirm it in a short visit, and it is worth knowing because insurers ask.

    Why does my water bill jump with no visible leak?

    A slab leak is the usual explanation in this housing type. Shut everything off and watch the meter; if it moves, the loss is real, and isolating sections narrows down where it is.

    Is a repipe through the attic acceptable?

    It is common here and leaves the pipe accessible, at the cost of running lines through a hot space and some ceiling patching. Insulation on the runs and a properly supported installation matter.

    Do I need a softener if the water is hard?

    It protects the heater and fixtures but adds salt, maintenance and a discharge line. The decision should follow a measured hardness number and what equipment you are trying to protect.

    Why is backflow protection required on irrigation?

    Because an irrigation system is a cross-connection between the outdoor water and the drinking water in the house. A failed device can draw contaminants back into the supply, so the requirement protects the property and the mains.

    Can I repair one slab leak instead of repiping?

    Sometimes, if it is genuinely isolated. The honest test is the history: several leaks in a few years generally means the pipe is failing, and repeated repairs keep taking out flooring.

    Sources and review date

    Reviewed on 2026-11-18.